How To Clean A Polyurethane Brush — Step By Step

Polyurethane is a composition of urethane and organic units in a polymer. It has many uses but is commonly used as a surface coating.

Polyurethane is a resilient substance great for making materials more durable and resistant to corrosion. It is most popularly used in the building and construction industry.

f:id:woodworkingrouteronline:20180716070808j:plain

The use of polyurethane in your home will make materials like your wall paint last longer.

A brush is normally used to apply polyurethane on various surfaces. You might want to clean your brush after using it with polyurethane, but how? Using water alone wont work, so you'll need an alternative.

This is how to clean a polyurethane brush:

Methods

The most popular method for cleaning a polyurethane brush is the use of paint thinner (mineral spirits).

Another method that is said to work, but isn't very highly recommended, is the use of Kerosene, although this method won't be covered in the article. You can find out more about it here.

Using Paint Thinner

For this method you will need:

  • a towel
  • paint thinner
  • lukewarm water
  • a plastic bowl
Steps in Cleaning a Polyurethane Brush
  1. First fill the plastic bowl halfway with paint thinner. This is because it's only the bristle or foam section that you need to apply the paint thinner to to get rid of the polyurethane.
  2. Dip the brush into the bowl with the paint thinner. Make sure the whole brush section is covered. You can add some paint thinner if needed.
  3. Leave your brush in the bowl for a 15-20 minute period. This will allow the paint thinner to fully penetrate into the polyurethane.
  4. Remove your brush from the plastic bowl, and then rinse it with lukewarm water. The use of cold water would end up hardening the brush. Using hot water is just as hazardous as it could loosen the glue holding the bristles, making them fall out.

Following the steps listed above will get your polyurethane brush clean in no time, which can then be used to paint other wood surfaces possibly cut with a special cutting. This will enable you to use it next time you need (for example, to paint other wood surfaces possibly cut with a special wood cutting tool) it instead of buying a new one.

To get the most out of the use of polyurethane, you should get premium brushes and re-use them.

Some Ways On How To Finish Pecky Cypress

Pecky cypress might be new terminology to anyone who has no interest in the different types of woods that nature offers.

Well, it's essentially cypress that has suffered from a fungus attack and developed many holes. Often it takes a long rectangular shape, and it also enjoys versatility in application.

f:id:woodworkingrouteronline:20180506064824j:plain

You could use it for different things including tables, ceilings, doors and the like.

Due to this holes in the wood surface, it is ideal to finish it before use, perhaps to take some of the sharpess out of the edges of the holes. 

How to finish pecky cypress is something many people have asked me about. Because of the texture of the wood, it might not be obvious what you should do differently than with some other type of wood.

Generally, there are a several different ways of effectively sealing the holes and other rough surfaces of pecky cypress, although pecky cypress can go just fine without any finishing.

This video reveals a way to enhance pecky cypress:

www.youtube.com

If you want to finish your pecky cypress, have a look at the methods below and their details:

Best Ways To Finish Pecky Cypress 

  • Use wax. 
  • Use oil and a sealer.
  • Apply satin polyurethane.
  • Do smoothening.

Wax: wax works well in filling the holes. Later, you may decide to paint it to cover up its look.

Oil and Sealer: The use of oil and sealer works well for smaller surfaces like tables. A good example is a common polyurethane sealer.

Satin Polyurethane: Two coats are ideal. Don't apply too much.

Smoothening: Smoothening can also be very helpful for finishing pecky cypress. Ideally, it involves the use of simple materials like sandpaper to remove the feelable grains. 

Given the above methods of caring for pecky cypress, which work well for any size, look or use, you ought not to worry the next time you acquire a bizarre piece of cypress in your site or project.

I wish you luck with your finishing project.

Top 3 Best Padlocks For Your Outdoor Shed

In this article, we will throw some light on some of the best padlocks for your outdoor shed.

These affordable locks will help to prevent any kind of theft or burglary from happening within your shed provided they are fitted properly.

f:id:woodworkingrouteronline:20180425232647j:plain

You might consider fitting these locks along with some sort of alarm which will make you more secure and safe.

For great padlock options, go here!

1. Guilty Gadgets - 50mm Secure Padlock

f:id:woodworkingrouteronline:20180425233238j:plain

This particular padlock is going to cost you a bit more than five dollars, but it's known to be extremely powerful in terms of locking a shed door.

One important thing to note is that this device has been built for outdoor usage. Although it includes a couple of keys, it is really great for the money when compared to other similar items on the market. At only a bit more than five dollars, it is going to do a very good job for you.

2. ABUS Outdoor Key Padlock TITALIUM 64TI/40

f:id:woodworkingrouteronline:20180425233259j:plain

Being manufactured by a reputed company named Abus, this padlock is arguably a superior option to the one mentioned above. In fact, the Abus padlock has been made from a quality material known as Titalium which helps it to last for years longer.

Apart from being extremely robust, this lock is also lightweight as well. It might be mentioned here that a top-quality aluminum alloy like Titalium is used for manufacturing certain components of airplanes these days.

3. Excell High Security Anti-Rust Padlock

f:id:woodworkingrouteronline:20180425233318j:plain

The Excell padlock definitely can compete among the other two mentioned in this list given that it is going to fulfill all the requirements of the user.

Although it is made from top quality laminated steel, the price of the product is only $14 and it helps to safeguard your tools in the best possible way.

This great lock is meant for securing garages, gates, and sheds which should be enough for you to fully comprehend its efficiency. Moreover, this padlock has received lots of positive reviews from customers.

No intruder will find it easy to break through this lock given that it features an innovative ball bearing locking system which is resistant to prying or pulling.

There are plenty of padlock options for your shed, and these are some of the best. For more padlock options, click the link above. Also be sure to take another step in your home-improvement efforts with a quality nailer recommended here. Good luck!

What You Should Do If You Are Looking To Get A CNC Router

Whenever we have to pick something, there are a lot of things we need to take into consideration. And something like a CNC router is no exception.

Since the goal of using such tools is molding, it is no surprise that picking the best possible option is on everybody's mind.

It doesn't really matter if you are going to be doing this for fun, or this is the career you chose for yourself. The need to get the most out of it is on the mind of every single individual.

So, what do you need to know before you actually commit to buying one for yourself or another person (or making your own at home - see Carve Your Creation)?

Routers Vs. Mills

The first thing that a lot of professionals like to emphasize is the difference between routers and mills.

The two might not seem like they differ that much, but the fact of the matter is that they do.

Scale is what we can start with. A router is much bigger in terms of what it can produce. If you are working with bigger pieces of material, then this one is an obvious choice. Depending on what type of stuff you will be dealing with also plays a role.

Routers are not the best when it comes to cutting certain types of metals, but they are the best if you want to make changes to the likes of plastics or carbons.

Holes are one of the key things people like to make when they are working with such machine. With routers, you can make much larger cavities, so that is another advantage to add to the list.

Quality

If there is one aspect that people tend to overlook for some reason, it would have to be the overall quality of the machine.

f:id:woodworkingrouteronline:20180419061141j:plain

Quite a few routers have this issue of becoming somewhat obsolete. That is, they start to require repairs or replacement parts after some time passes.

The period depends on how frequent you are using the machine. But the bottom line is that these changes will cost you quite a hefty sum.

What To Do

So what should one do to make sure that there will be as little problem in the future as possible?

Well, it should be obvious that you need to research everything as much as possible. Start by visiting your local stores and asking for information. Employees have experience with this sort of thing and they will be able to tell you what you want know. Internet is also great if you want to delve further into the subject.

Whatever the case may be, getting a CNC router is a lot of work. Especially if you haven't had it before. So before you purchase it, be cautious and find out as many details as you can.